STILLWATER -- As Oklahomans clean up after the recent ice storm that left tree limbs shattered or lying around, care should be taken to ensure protection against unintentionally risking an arm or leg being added to the toll.
"To prepare yourself, carefully study the operator's manual so that you're thoroughly familiar with all aspects of safe operational procedures," said Craig McKinley, Oklahoma State University Cooperative Extension forestry specialist. "Before you operate a particular saw for the first time -- and periodically thereafter -- you should carefully review the owner's manual."
New saws come with a manual, but if lost, a copy can be obtained from the manufacturer. Manuals offer proper operating procedures as well as detailed information about recommended maintenance practices to keep the saw running smoothly and safely.
Once the operator has honed his knowledge of the saw, the chain itself needs to be sharpened.
"When the chain is dull, you increase the effort needed to cut through a piece of wood," McKinley said. "At the same time, you increase the possibility of injury to yourself and damage to the saw."
Sharpening instructions are typically outlined in the operating manual and is a relatively easy task. However, the recommended filing and depth guides are essential to assure the proper angle on the cutters and cutting depth for maximum cutting efficiency.
Whenever a chain is being sharpened, gloves should be worn or a rag placed over the chain to protect hands from the sharpened cutters. A sharp chain is only effective if there is proper chain tension and lubrication.
"Chain tension should be adjusted to ensure quick, smooth cutting action," McKinley said. "Too loose a chain will derail, too tight a chain will bind."
A cold chain should be tightened to where the chain hangs about 1/32 of an inch away from the bar rails at the center of the bar span. Warm chains should be adjusted to about a 1/8 inch gap.
While the saw is in use, be sure to pump the oiler frequently to prolong the life of the chain. Periodically stopping the engine and pumping the oiler while pulling the saw chain around by hand will provide a good, even oiling of the chain. However, the motor needs to be turned off and the spark plug wire disconnected for this process.
Chain saws with automatic chain oilers may need an extra squirt occasionally for proper lubrication. Many new saws do not have a manual oiler, so making sure the oiling port is functioning so that the oil is reaching the chain is recommended. The presence of smoke while the chain is operating is a good indication of lack of oil, and perhaps a dull chain.
Additional tips for chain saw care are available online on Oklahoma State University's Division of Agricultural Sciences and Natural Resources Web site, http://www.dasnr.okstate.edu, on the Internet.
Fashion also plays a role in safe use of chain saws. A hard hat should be worn, along with safety goggles or eye glasses, ear muffs or ear plugs, lightweight gloves, work boots or shoes and fitted clothing.
McKinley said clothes should not hang loosely from the body as they might become tangled in the saw. Also, the use of nylon mesh protective leg chaps or kneepads can help protect the operator's legs.
"Saw-related back-up equipment is also important," he said.
Back-up tools include an ax, sledgehammer, wedges, sharpening file, screwdriver and wrench for throttle and chain adjustments, as well as chain oil, a funnel and plenty of fuel. Readily available shovels and a fire extinguisher should also be considered.
With the proper safety gear, back-up materials and a prepared saw, the operator is ready to begin cutting.
The saw should be started in an open, level surface as close to the work area as possible. Holding the saw firmly against the ground with one hand on the front handle and the inside of one knee on the rear handle, pull the starter rope briskly to give the engine a rapid spin.
"Don't yank the cord out to the very end; this could damage the starter mechanism," McKinley said. "Also, hold the grip and let the starter cord rewind evenly instead of letting it snap back."
When carrying the saw, the chain should be in the rear with the muffler away from the operator's body.
When operating the saw, maintaining balance is a must. McKinley warns a chain saw is not forgiving when mistakes are made by its operator. A solid grip with both hands, making sure fingers and thumbs completely encircle the handle, will allow for greater control.
"Cut with the lower side of the saw as much as possible," McKinley said. "This is the safest and least tiring position."
Cuts should be made with the wood near the middle of the saw.
"With elbows and knees slightly flexed, the saw should be operated at the side of your body so that it will not swing into your body if it suddenly kicks back," McKinley said.
Kickback results when the saw jumps toward the operator after hitting a solid object with the front of the saw. The engine torque is transferred to the guide bar, which causes the saw to rotate in a rapid motion.
"Kickback is the most dangerous of all chain saw hazards," McKinley said. "The most common cause of kickback is that small, hidden limb that catches the upper quadrant of the bar nose."
There are several scenarios that will cause kickback. However, the force will be increased by a dull chain, chase tension that is too loose and blind-cutting or boring with the bar nose.
"Kickback is responsible for about a third of the serious injuries that occur each year with chain saws," McKinley said. "Avoiding kickback should be a major concern of all chain saw operators."
Once the cutting is complete, there are some recommended steps to proper storage of the saw, beginning with stopping the engine and draining the fuel tank in a safe area. Then, the engine should be restarted and run at idle to remove the remaining gas from the engine.
The chain can then be removed and stored in a container of oil and the spark plug wire should also be disconnected to reduce the possibility of accidental starting.
McKinley said following these procedures allows those with tree and limb damage to clear their property back of debris in a relatively safe manner. However, even with cautious operation, the threat of injury or death still exists.
Outdoors
February 11, 2010
Safety is vital when working with chain saws
- Outdoors
-
- Safety is vital when working with chain saws STILLWATER -- As Oklahomans clean up after the recent ice storm that left tree limbs shattered or lying around, care should be taken to ensure protection against unintentionally risking an arm or leg being added to the toll.
- Dolese Youth Park Pond teeming with trout for young anglers Oklahoma City resident Gaston Gallant goes fishing nearly every day of the two-month trout season at Dolese Youth Park Pond, a northwest Oklahoma City fishing destination currently teeming with nearly 2,600 rainbow trout.
-
De-icing salt can harm landscape plants
Each winter, millions of tons of deicing salt are applied to state and municipal roads to keep the roads safe for vehicles to travel. Salt is spread near houses to avoid pedestrian injuries. This is necessary for safety, but did you know excessive salt can cause widespread damage to trees ? possibly leading to permanent decline and even death?
According to the Tree Care Industry Association, a non-profit organization dedicated to the tree care industry, even severe salt damage might not be visible on a tree until the end of summer, leaving homeowners wondering what might have caused the problem. - Making it through That was a cold spell of what we used to call "Biblical proportions." It was made perhaps more interesting locally by the old heat-pump in the house, which died on New Year's Eve. For a week, the household was maintained by an old Franklin stove in the living room, and by the old owner, who had to carry in firewood so it could be fed every hour or so.
- University of Oklahoma team wins college fishing event ZAPATA, Texas -- The University of Oklahoma team of Mark Johnson and Chip Porche won the National Guard FLW College Fishing Texas Division event on Falcon Lake Saturday with six bass weighing 34 pounds, 8 ounces.
- Great Western Feedout entry deadline Friday It is time to start entering for the Great Western Feedout of 2010. For those of you not familiar with it, the Great Western Feedout is a producer information feedback program that allows cattle producers the opportunity to evaluate the genetic merit of the calves they produce for feedlot performance and carcass value following weaning and a winter stocker program.
-
Part-time lakes are of full-time importance
For the unlearned, old age is winter, for the learned, it is the season of harvest.
--Hasidic saying
Today's topic is the most important wetlands you've never heard of: Playa lakes and oxbow lakes. Playa lakes are usually saucer shaped natural low places with clay bottoms located in dry landscapes. - Christmas Bird Count yields unexpected rewards What am I doing here? It is incredibly cold morning and I am crouched here in the dark in the willows on the banks of the South Canadian River with a few stalwarts indulging in an activity called "owling.
-
Increasing deer population leads to ornamental and garden plant damage
STILLWATER -- With more than a half million white-tailed deer in Oklahoma, many landowners experience nature in its purest sense as the deer can be viewed at close range.
However, this has become a problem over the years as the deer population has increased, forcing thousands of these animals into peripheral suburban areas, leaving homeowners to deal with damage to ornamental and garden plants. -
Wildlife Department to host town hall meeting
Sportsmen will have an opportunity to voice their thoughts on wildlife, hunting and fishing related issues at a town hall meeting hosted by the Oklahoma Department of Wildlife Conservation.
The meeting, one of a series, is set for 7 p. - More Outdoors Headlines
